Ethernet Cable CAT6, 2m
$40.99This cable is used to connect the infrared camera to Ethernet.
Showing all 18 results
-
-
Hard case for the FLIR A400/A700 Series (T300163)
$270.00This hard case is an accessory for the following products:
- FLIR A400/A700 Thermal Smart Sensor configuration
- FLIR A400/A700 Thermal Image Streaming configuration
- FLIR GF77a
-
Hard Transport Case (T197871ACC)
$276.99- Black Waterproof Case
- For FLIR A3xx, A6xx Series Thermal Imaging Cameras
-
RHP Boson RC-IF Remote Control Interface
$399.00Ideal for sUAS and UAV Operations
- 6 to 26 Volts DC Input
- Reverse Polarity Protection
- Control w/RC Receiver
- S-Bus & PWM
- USB Video Support
- Color Palette Selection
- (FFC) Flat Field Correction Shutter Control
- (DDE) Digital Detail Enhancement
- Thermal AGC
- Continuous Digital Zoom
- 2 Composite Video Outputs
- USB Video Output
- 5.8 grams
Select options This product has multiple variants. The options may be chosen on the product page -
Teledyne FLIR 4in. Blackbody Source for ALC & Supplemental FFC
$2,122.00FLIR 12V 4″ Blackbody Source for ALC & Supplemental FFC, offers a uniform temperature source for FLIR Tau 2 Thermal Cameras. Low cost 4-inch blackbody which provides a uniform temperature source when using FLIR’s Alt Lens Cal software to field-calibrate lens-less Photon or Tau cameras with third-party lenses, or to take advantage of the Supplemental…
-
Teledyne FLIR BOSON Boson VPC Cable
$42.00Single USB interface cable for the Boson VPC with USB-C to USB-A Cable and BNC.
-
-
-
Teledyne FLIR BOSON VPC Accessory with USB Cable
$193.00Single USB interface to Boson with USB-C to USB-A Cable
-
Teledyne FLIR BOSON VPC Accessory with USB-ANALOG CABLE
$217.00Boson USB / Analog Video Power Connector (VPC) Kit
-
Teledyne FLIR IR Windows
- Reduces the need to open cabinets for inspections
- May reduce the need for layers of heavy protective gear*
- Easy to install
- Shortens inspection time
- Cuts the cost of inspections
*Personal protective equipment (PPE) may still be required as determined by your plant safety personnel.
-
Teledyne FLIR Tau NFOV Lens Holder
$58.00Teledyne FLIR NFOV Lens Holder for the FLIR TAU 2 Thermal Cameras
-
Teledyne FLIR TAU WFOV Lens Focus Tool
$70.00The Tau Focus Tool can be used to change the focus of the wide field of view (WFOV) 5.5mm, 7.5mm, 9mm, 13mm, or 19mm lenses.
-
Teledyne FLIR Tau WFOV Lens Locking Ring
$24.00The lens locking ring is designed to mount a Tau WFOV camera into a bulkhead. The M29 x 1.0 thread on the outside of the lens mount flange is placed through the clearance hole in the bulkhead and the O-ring seals the camera to the face. The Type 2-025 O-ring is not for sale through…
-
Teledyne FLIR Tau WFOV Lens Mount – Locking Ring Install / Removal Tool
$82.00The lock nut tool will attach to a torque wrench for proper tightening of the lens locking ring. Torque the locking ring to 4.0 in-lbs.
-
Transport Case
$197.99- Black Waterproof Case
- For FLIR Ax5 Series Thermal Imaging Cameras
- 10.75″ x 9.75″ x 4.75"
-
Teledyne FLIR Boson Development Board
$1,022.00Full access to Boson 80-pin interface allows connection to:
- USB 3
- 100/GigE Ethernet
- CameraLink
- Serial Com
- Micro SDCard
- I2C
- SPI
- SDIO
- VSYNC/RESET
- GPIO
-
Teledyne FLIR Boson MIPI Development Accessory Board
$407.00Boson MIPI development board provides the option of a digital data protocol typical of a MIPI CSI v1.1, and DPHY 1.0 camera in a software configurable single or dual lane configuration.
- Pixel Formats:
- RAW8 (monochrome, post-AGC)
- 16-bit UYVY (color, post-AGC)
- RAW14 (pre-AGC)
- Single Channel Mode:
- Monochrome 8-bit
- Monochrome 14-bit
- Post-AGC 8-bit monochrome
- Post-AGC 16-bit color YUV422 (UYVY)
- Dual Channel Mode:
- Monochrome 8-bit & Monochrome 14-bit
- Post-AGC 16-bit color YUV422(UYVY) & Monochrome 8-bit
- Post-AGC 16-bit color YUV422(UYVY) & Monochrome 14-bit
- MIPI DDR clock rate: 246 MHz
- Latency: <4.8ms
NOTE: This test board is available for development purposes to fan out several of the interfaces provided on the primary I/O connector.
It is not intended to be integrated into final end-use products.
Design and fabrication of an additional interface board is recommended for non-development use cases. - Pixel Formats: