Add-Ons & Components

“USB 3.1 Cable Type C” has been added to your cart. View cart

Showing 81–91 of 91 results

Transport Case
$197.99
- Black Waterproof Case
- For FLIR Ax5 Series Thermal Imaging Cameras
- 10.75″ x 9.75″ x 4.75"
Add to Cart
USB 2.0 Cable – USB2-A-B-6 – 6Ft Type A to Mini B
$11.95
USB2.0 Cable – USB2-A-B-6 – 6Ft Type A to Mini B

Add to Cart
USB 3.0 Cable Type A/Micro B
$29.00
- USB 3.0 cable
- End 1: USB 3.0 (Type-A)
- End 2: USB 3.0 (Micro-B) Locking screws
- 3 m in length
Add to Cart
USB 3.1 Cable Type C
$34.00
- USB 3.0 cable
- End 1: USB 3.0 (Type-A)
- End 2: USB 3.0 (Micro-B) Locking screws
- 3 m in length
Add to Cart
RHP-BOS-DSU2-IF Dual Sensor USB 2 Board for Boson and E/O
- Dual USB Video over single interface
- Optically Centered
- 2x additional USB ports for other sensors or cameras
- Small form factor
- Wide input range 5-17 VDC
- Ideal for Drone, UAV, UGV Implementation
- No drivers Required
- Compatible with Windows, Mac and Linux Operating systems
Add to Cart
Teledyne FLIR Neutrino LC Demonstration Lens

A 22mm fixed focal length, f/5.5 lens provides a 25° horizontal field of view (HFOV). Includes a mechanical housing for the lens and allows for focus capability via keyed lens barrel and threaded barrel/housing.
RHP Boson Video Controller
Works with these RHP Boson Interface Assemblies:
Instantly Download Below
Add to Cart
RHP Boson Camera Controller Application
Works with these RHP Boson Interface Assemblies
Instantly Download Below
Add to Cart
Teledyne FLIR Boson Camera Link Accessory
$600.00
- Camera Link and USB interface to Boson video
- converts Bosons CMOS video
- Standard SDR-26 receptacle
- USB-3 micro-B connection
Add to Cart
Teledyne FLIR Boson Development Board
$1,022.00
Full access to Boson 80-pin interface allows connection to:
- USB 3
- 100/GigE Ethernet
- CameraLink
- Serial Com
- Micro SDCard
- I2C
- SPI
- SDIO
- VSYNC/RESET
- GPIO
Add to Cart
Teledyne FLIR Boson MIPI Development Accessory Board
$407.00
Boson MIPI development board provides the option of a digital data protocol typical of a MIPI CSI v1.1, and DPHY 1.0 camera in a software configurable single or dual lane configuration.
- Pixel Formats:
  - RAW8 (monochrome, post-AGC)
  - 16-bit UYVY (color, post-AGC)
  - RAW14 (pre-AGC)
- Single Channel Mode:
  - Monochrome 8-bit
  - Monochrome 14-bit
  - Post-AGC 8-bit monochrome
  - Post-AGC 16-bit color YUV422 (UYVY)
- Dual Channel Mode:
  - Monochrome 8-bit & Monochrome 14-bit
  - Post-AGC 16-bit color YUV422(UYVY) & Monochrome 8-bit
  - Post-AGC 16-bit color YUV422(UYVY) & Monochrome 14-bit
- MIPI DDR clock rate: 246 MHz
- Latency: <4.8ms
NOTE: This test board is available for development purposes to fan out several of the interfaces provided on the primary I/O connector.
It is not intended to be integrated into final end-use products.
Design and fabrication of an additional interface board is recommended for non-development use cases.
Add to Cart