Transport Case
$197.99- Black Waterproof Case
- For FLIR Ax5 Series Thermal Imaging Cameras
- 10.75″ x 9.75″ x 4.75"
Showing 81–91 of 91 results
-
-
USB 2.0 Cable – USB2-A-B-6 – 6Ft Type A to Mini B
$11.95USB2.0 Cable – USB2-A-B-6 – 6Ft Type A to Mini B
-
USB 3.0 Cable Type A/Micro B
$29.00- USB 3.0 cable
- End 1: USB 3.0 (Type-A)
- End 2: USB 3.0 (Micro-B) Locking screws
- 3 m in length
-
USB 3.1 Cable Type C
$34.00- USB 3.0 cable
- End 1: USB 3.0 (Type-A)
- End 2: USB 3.0 (Micro-B) Locking screws
- 3 m in length
-
RHP-BOS-DSU2-IF Dual Sensor USB 2 Board for Boson and E/O
- Dual USB Video over single interface
- Optically Centered
- 2x additional USB ports for other sensors or cameras
- Small form factor
- Wide input range 5-17 VDC
- Ideal for Drone, UAV, UGV Implementation
- No drivers Required
- Compatible with Windows, Mac and Linux Operating systems
-
Teledyne FLIR Neutrino LC Demonstration Lens
A 22mm fixed focal length, f/5.5 lens provides a 25° horizontal field of view (HFOV). Includes a mechanical housing for the lens and allows for focus capability via keyed lens barrel and threaded barrel/housing.
-
RHP Boson Video Controller
Works with these RHP Boson Interface Assemblies:
- Low Profile BOSON VPC
- Low Profile BOSON VPC3
- RHP-BOS-USBC-IF
- RHP Boson Camera Link Interface Board
- RHP Boson LVDS Encoder Board
- RHP BOSON VPC TTL Interface Module
- RHP IP LVDS Encoder Board
Instantly Download Below
-
RHP Boson Camera Controller Application
Works with these RHP Boson Interface Assemblies
- RHP BOSON RC-IF REMOTE CONTROL INTERFACE
- RHP BOSON RC-HD-IF REMOTE CONTROL INTERFACE
- RHP-BOS-DS-IF DUAL THERMAL SENSOR INTERFACE
Instantly Download Below
-
Teledyne FLIR Boson Camera Link Accessory
$600.00- Camera Link and USB interface to Boson video
- converts Bosons CMOS video
- Standard SDR-26 receptacle
- USB-3 micro-B connection
-
Teledyne FLIR Boson Development Board
$1,022.00Full access to Boson 80-pin interface allows connection to:
- USB 3
- 100/GigE Ethernet
- CameraLink
- Serial Com
- Micro SDCard
- I2C
- SPI
- SDIO
- VSYNC/RESET
- GPIO
-
Teledyne FLIR Boson MIPI Development Accessory Board
$407.00Boson MIPI development board provides the option of a digital data protocol typical of a MIPI CSI v1.1, and DPHY 1.0 camera in a software configurable single or dual lane configuration.
- Pixel Formats:
- RAW8 (monochrome, post-AGC)
- 16-bit UYVY (color, post-AGC)
- RAW14 (pre-AGC)
- Single Channel Mode:
- Monochrome 8-bit
- Monochrome 14-bit
- Post-AGC 8-bit monochrome
- Post-AGC 16-bit color YUV422 (UYVY)
- Dual Channel Mode:
- Monochrome 8-bit & Monochrome 14-bit
- Post-AGC 16-bit color YUV422(UYVY) & Monochrome 8-bit
- Post-AGC 16-bit color YUV422(UYVY) & Monochrome 14-bit
- MIPI DDR clock rate: 246 MHz
- Latency: <4.8ms
NOTE: This test board is available for development purposes to fan out several of the interfaces provided on the primary I/O connector.
It is not intended to be integrated into final end-use products.
Design and fabrication of an additional interface board is recommended for non-development use cases. - Pixel Formats: